Видео

Why no rebar?

Good to see another video, nice truck and trailer😀

I tried helping a neighbor on his Deere 5065E. I am not familiar with tractors, but his won't start and shows pto light, dirty exhaust filter, and exclamation point. I disconnected the neutral sensor and then used a jumper. I also unplugged pto 5 or 6 pin plug and the light turned off on dash. Any help will be appreciated.

Sounds good always like that M11 sound the Red head N14 also that Louisville 9000 looks great I drove a 75 LNT 9000 tandem tractor 250 Cummins turbo 8 spd RR

…really like this work of yours Brings back fondest of memories • We had / operated for agri development a D6B of the early seventies One with ripper attachment, same blade configuration no turbo but direct start and drive as well I fell in Love with the D6’s and D7’s then The versatility and ease of operation of these is and power onto the blade and ripper was absolutely a mind blast ~ and one could see where you dozed, which helped stacks Thanks for showing and sharing Much appreciated Pity this one has shocking grasper plates…and some missing covers, plates Beste ex ZA‼️ Pse carry on with your work… 👊🔥 🪖

Can you still find parts. History channel.

Have you ever tried to bale with the 5200?

Hi Dennis, Where did you order your clutch packs from? Do you know if they make new brake bands? Thanks

I saw that it takes two batteries so I assume it is a 24V system, I recently got one in ok condition. What type of batteries are you using

What is a kimco winch?

Boring only filming where ya Been not where you going or shifting gears

I need a easy way to remove the piston on my 163cc engine build from power washer that was badly rusted in the inside and was stuck and gust got the card and need new piston rings no compression just back fires loudly

GOOD Memories Dennis! Thankyou for sharing your knowledge and taking us along with you!

Do you bale with the mx5200 too?

Thanks for not showing much about pins

It's fun watching the old allis dozer gettin' er done ‼️

Awesome little dump truck

Great video keep them comming and lovely little machine with that blade would love to have it haha

Great video Dennis, nice seeing a good operator applying his craft

Nice pond, great job as usual

Good to see your work. Happy new year.

Love these dressers I've operated just about everything on tracks an dresser is my favorite,,especially in this size,,

Do you have any video on removing an axel?

I have an HD5G track loader that I have that project going on with. Steering clutches are the same between 5 and 6. Nice video‼️

I had to replace the rear end bevel gear and transmission on my hd6

shoulda put a thickened edge around the boarder to prevent water washing out your base, also prevents your slab from floating away/breaking into pieces over time. js.

never owned an excavator, but a 4x4 backhoe is almost indispensable.

kind of brings back memories, my dad had an HD6 very similar to yours and a TD20c in Alaska placer mining when i was a kid, i really enjoy watching your videos.

PJ? The paint will be flaking off of it in no time. You might consider a bigger truck too.

Now you’re walking in tall cotton!

I just got a early 1960ish Case 530not sure of model tag is gone. Hoe and Loader are model 31. need to change gas engine. any info would be appreciated? Not sure if any 1960s 530 book pertains to tractor.

Where did you get a Harley Davidson air conditioned dozer???

I have ran the old girl, they are a beast but when you said workout I lost it 🤣

The glass looks flat meaning cheaper to replace vs the new super curved crap.

❤❤❤🎉

Tebrikler ⭐️👏

I ran a 7wat trailer plug also, I've got the 14pin plug, so I just piggybacked behind it after I found which wires went to my joystick controls

I have a friend that just got a used 2022 t770 that is basic, starts with a key & does not have the display panel on the upper left or a back up camera. I helped him install an aftermarket backup camera & noticed there is a plug for the display panel on the upper left. If we buy that display panel, will it work & show the read outs of the engine & hydraulics??

Although grinding marks are common on those casting mold sprue channels. They were ground rather sloppy. But, the flash on the inside and the filler indicate a poorly maintained mold. Another indication of shoddy workmanship is the large mold seam flash running down both sides of the part. They indicate the mold halves were out of alignment. You will always have a seam, but those are too large. Splitting failures are likely due to the mismatch of the mold sections. I was a Corporate Quality manager for a large company that had both iron casting and plastic molding factories… that piece should have been melted down and recast in a totally refurbished mold. Send it back and buy from a supplier who sources their parts from a different manufacturer. Good seeing you Dennis!

😂

You need a refund 😂😂😂 that’s absolutely horrible

Wym bro that’s quality parts in 2023

Yep… I’ve bought several parts from them. PS: I ain’t a fortune teller but, I see a sizable rebuild in your future!

Nice parts !

Love this Thank you for sharing your knowledge.

Awesome

Awesome addition

cant wait for more content with this one great machine congrats

cant wait to see content with this one gonna be good machine for sure love the blade

Cat 🐈